Scrambler Scrambler 1200 Suspension

Discussion in 'Thruxton, Scrambler & Trident' started by Repooh, Apr 15, 2020.

  1. Bug

    Bug Well-Known Member

    Apr 29, 2020
    149
    93
    Aylesbury
    Fitting heavier TEC rear springs this week .... will post how I get on
     
  2. Burny_13

    Burny_13 Active Member

    Jun 16, 2019
    67
    28
    Reading
    It is not unreasonable for any manufacturer to build a bike to the average customer, they can not tailor for all, so going with the average is good!
    At least they engineer the remaining parts of the bike in order to cope with that well outside of the average scope so you can make these adjustments without worrying about the frame strength for example.
    220kg load capacity is excellent and at the higher end of the scale of things.
    the fact that they have set the factory specs to suit a 70-90kg solo rider is exactly what I would do as this is the average use the bike would recieve (globally)

    Count yourself lucky. It was only after buying an MT-10 that I found out that my rider & Pillion + gear weight was only 4kg of the bikes rated maximum... so we couldnt even take any luggage!
     
  3. Repooh

    Repooh Rarely Satisfied

    Jan 5, 2018
    1,430
    1,000
    Stabby Town
    Keep us posted please Bug, I was trying to work out if the stiffer spring would give me the same ride height on zero pre-load vs the std spring with max pre-load. I could do with gaining back the precious inch lost to max pre-load
     
    • Like Like x 1
  4. Bug

    Bug Well-Known Member

    Apr 29, 2020
    149
    93
    Aylesbury
    Will do. Might be next week now as I am still waiting for a jack to arrive ☹️
     
    • Thanks Thanks x 1
  5. Bug

    Bug Well-Known Member

    Apr 29, 2020
    149
    93
    Aylesbury
    Jack arrived today and assembled ...... let the transformation begin ..... roll on tomorrow
     
  6. Bug

    Bug Well-Known Member

    Apr 29, 2020
    149
    93
    Aylesbury
    Springs fitted today .
    Bike on front and rear paddock stand .
    Measurements from the centre of the bolt holding grab rail to bottom bolt retaining rear ohlins unit, as follow:
    Bike on ratchet straps , no loading on suspension 5200mm
    Bike with new heavy springs at rest 4700mm
    With fat bloke on board 4200mm ☹️
    Will dial in preload tomorrow...... hope fully get it to 750mm sag.
    Bug
     
  7. Bug

    Bug Well-Known Member

    Apr 29, 2020
    149
    93
    Aylesbury
    Sorry ...take a decimal point off each measurement.
     
  8. Repooh

    Repooh Rarely Satisfied

    Jan 5, 2018
    1,430
    1,000
    Stabby Town
    So how's the suspension post the Tec springs
     
  9. Bug

    Bug Well-Known Member

    Apr 29, 2020
    149
    93
    Aylesbury
    Great improvement with TECsprings. Took bike out for test run today ......it feels better than ever . I am ashamed to say I am 266lb . Dialled in 5 full turns preload on the rear . 14 compression. 17 rebound.
    Front 13 full turns preload. 2 turns comp and rebound.
    Bike gives you great feedback and loads of confidence when cornering.
    Have not checked seat height yet ...... but will not go back.
    Great job TEC parts
     
  10. Repooh

    Repooh Rarely Satisfied

    Jan 5, 2018
    1,430
    1,000
    Stabby Town
    Good to hear glad it's worked out for you
     
Loading...

Share This Page