Featured Thunderbird 650 Electric’s

Discussion in 'Vintage Classics' started by Ethan, Mar 5, 2019.

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
Page 2 of 4
  1. Tricky-Dicky

    Tricky-Dicky Crème de la Crème

    Dec 12, 2016
    2,441
    1,000
    Norfolk UK
    #21 Tricky-Dicky, Mar 5, 2019
    • Useful Useful x 3
    • Like Like x 2
    • Agree Agree x 1
  2. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #22 Ethan, Mar 31, 2019
    Hi so I have finally removed the primary cover and there is no alternator fitted looks like a spacer has been fitted to remove the alternator, but now I have another concern the threaded bar that runs through the smaller sprocket wasn’t wound in tight and I am just wondering do I wind it back to the sprocket and nip the nut on the end up ??
    Thanks in advance Ethan.

    image.jpg

    image.jpg
     
    • Like Like x 3
  3. Tricky-Dicky

    Tricky-Dicky Crème de la Crème

    Dec 12, 2016
    2,441
    1,000
    Norfolk UK
    #23 Tricky-Dicky, Mar 31, 2019
    Yes it should be tight...but you should be looking to fit an alternator or you will only have lights for as long as the battery charge lasts.
     
    • Agree Agree x 2
  4. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #24 Ethan, Mar 31, 2019
    Is an alternator only something I could find second hand or is there somewhere that makes a replacement still thanks Ethan .
     
    • Agree Agree x 1
  5. Tricky-Dicky

    Tricky-Dicky Crème de la Crème

    Dec 12, 2016
    2,441
    1,000
    Norfolk UK
    #25 Tricky-Dicky, Mar 31, 2019
    • Agree Agree x 2
  6. Taff

    Taff Member

    Nov 27, 2018
    31
    18
    Cymru
    #26 Taff, Apr 13, 2019
    Do your research. Loads of info on pre unit triumphs on inter web.
    Read the manual from classicbike.biz.
    Also get a parts manual.
    You will need to fit an alternator to hold the sprocket on the crankshaft. The hand tight stud will need to be torqued up with the rotor in place.
    Don’t run it as it is as it will run like that as it’s got a magneto ignition system but the sprocket will be loose.
    I’ve got 2 pre unit 650s. They’re great bikes. You’ll love it when you get out on a sunny day. Good for 100mph. The bike that gave the bonneville and Thruxton their names.
    The brakes are not as good as the motor so think ahea
    d.
    Ask if you need any more info. I might bore you to death on these babies.
    Taff
     
    • Like Like x 2
    • Agree Agree x 1
  7. Adie P

    Adie P Crème de la Crème

    Jul 7, 2018
    3,662
    1,000
    MID DEVON
    #27 Adie P, Apr 13, 2019
    Ethan,

    Along with the alternator stator and rotor, I assume you'll also need a regulator/rectifier and the sub-harness wiring to connect them.

    The Thunderbird is often considered the sweetest of the 650's - nice power/torque output without being bonkers - and yours is a really lovely example. Definitely worth any investment required in cost, time and effort - the rewards will be fully repaid.
     
    • Like Like x 1
    • Agree Agree x 1
  8. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #28 Ethan, Apr 27, 2019
    Hi quick update I ended up just running the lights off a charged battery so I could get the bike out, after a service new oil plugs and tyres it wasn’t running well and was leaking oil from head gasket and push rod tubes,so I have the head off the bike and I am just wondering if there is good and bad gasket sets or if they are all similar copper head gaskets thanks again.
    (It has a 9 stud head stamped 69 on the inside of it)
     
    • Like Like x 1
    • Useful Useful x 1
  9. darkman

    darkman Crème de la Crème

    Oct 26, 2015
    7,634
    1,000
    Southcoast of the UK Earth
    #29 darkman, Apr 27, 2019
    Head gaskets should not leak oil as there are no oil ways between head and barrels, you old copper gasket can be reused by annealing it. The most important part is using the correct seals and getting the crush correct.
     
    • Like Like x 2
    • Agree Agree x 1
  10. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #30 Ethan, May 22, 2019
    Hello again I have fixed the problem with the head I stripped it and changed all the gaskets I think it was a leaky push rod tube running down into the fin between the head and barrel but that’s all fixed now, I am onto my next problem and would love some advice I am trying to remove the clutch hub and I have the clutch puller tried that and it didn’t work it is really stuck on there I can’t seem to free it off the shaft any advice would be greatly appreciated as always thanks in advance Ethan.
     
    • Like Like x 2
    • Agree Agree x 1
  11. darkman

    darkman Crème de la Crème

    Oct 26, 2015
    7,634
    1,000
    Southcoast of the UK Earth
    #31 darkman, May 22, 2019
    Tighten the puller and hit it with a hammer and retighten and hit again to shock it off.
     
    • Like Like x 1
    • Agree Agree x 1
  12. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #32 Ethan, May 22, 2019
    I tried that but it didn’t budge at all seems to be really stuck on
     
    • Agree Agree x 1
  13. darkman

    darkman Crème de la Crème

    Oct 26, 2015
    7,634
    1,000
    Southcoast of the UK Earth
    #33 darkman, May 22, 2019
    Heat with a gas torch might help.
     
    • Like Like x 1
    • Agree Agree x 1
  14. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #34 Ethan, May 22, 2019
    I will try that next if that doesn’t work so you think it can be cut off and replaced ?
     
    • Agree Agree x 2
  15. darkman

    darkman Crème de la Crème

    Oct 26, 2015
    7,634
    1,000
    Southcoast of the UK Earth
    #35 darkman, May 22, 2019
    Have faith and getit hot :), at the death you could grind 2 flats and split it with a sharp chisel :-(
     
    • Agree Agree x 1
  16. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #36 Ethan, Jun 16, 2019
    In the end I had to do as you suggested and grind and chisel it got it off and replaced all back together running perfect almost no oil leaks now (just small gearbox leak).
    Brings a huge smile to my face every time I take it out just thought I’d say thank to you all for the info very much appreciated,thought I’d share a few pics from today.
     
    • Agree Agree x 1
  17. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #37 Ethan, Jun 16, 2019
    [​IMG]
     
    • Like Like x 1
  18. joe mc donald

    joe mc donald Joe
    Subscriber

    Dec 26, 2014
    14,585
    1,000
    slough / burnham
    #38 joe mc donald, Jun 16, 2019
    Ethan.
    Great Job.
    Joe
     
    • Like Like x 1
    • Agree Agree x 1
  19. Ethan

    Ethan Well-Known Member

    Mar 5, 2019
    69
    63
    York
    #39 Ethan, Jun 16, 2019
    Just a couple from today

    B86FD5FC-F523-4B7A-8AF0-D8327F7A1014.jpeg

    83C1782C-53A3-4DB0-B612-BA0BF371B94A.jpeg
     
    • Like Like x 7
  20. joe mc donald

    joe mc donald Joe
    Subscriber

    Dec 26, 2014
    14,585
    1,000
    slough / burnham
    #40 joe mc donald, Jun 16, 2019
    Ethan
    Give your self a big pat on the back. It's fantastic. Great to see the old bikes still out there looking great.
    Regards
    Joe.
     
    • Agree Agree x 3
    • Like Like x 1
Page 2 of 4
Loading...
Similar Threads - Thunderbird 650 Electric’s
  1. D. McKeegan

    1954 Triumph 6t 650 Thunderbird

    D. McKeegan, Sep 19, 2023, in forum: Parts, Accessories & Clothing
    Replies:
    3
    Views:
    909
    darkman
    Sep 22, 2023
  2. MikeF00

    Triumph Thunderbird 650 circa 1965

    MikeF00, Nov 18, 2014, in forum: Builds & Projects
    Replies:
    2
    Views:
    1,361
    Recycled Rocker
    Nov 19, 2014
  3. Minton

    Lifting Thunderbird

    Minton, Jan 26, 2025, in forum: Technical Help
    Replies:
    3
    Views:
    402
    joe mc donald
    Jan 31, 2025
  4. Stu9000

    Thunderbird 900 Wont Start

    Stu9000, Oct 31, 2024, in forum: Technical Help
    Replies:
    6
    Views:
    593
    joe mc donald
    Nov 3, 2024
  5. Pappa583

    Thunderbird 1700 Storm Engine

    Pappa583, Oct 7, 2024, in forum: Technical Help
    Replies:
    3
    Views:
    474
    Saxon 59
    Oct 27, 2024

Share This Page

Sign up