Clear Wrapping?

Discussion in 'Speed Triple' started by Moe, May 3, 2017.

Tags:
  1. Moe

    Moe Senior Member

    Jun 10, 2015
    290
    113
    Colchester
    Hi all,

    Thought I'd ask everyone's views on wrapping your motorcycle panels to protect it..

    Your thoughts please!

    I'm considering wrapping in clear, so not to detract from the bike just add that protection from swirls.

    Got a quote from a local one said £850 + vat!!

    Potentially will try it myself!
    Thanks,
     
  2. MrOrange

    MrOrange Guest

    Have done this, but never in the clear stuff. Used signwriting stuff, to protect rear faring and tank during touring holidays and also the carbon look wrap stuff on bike side panel, cos Suzuki use the cheapest grey plastic for them.

    Not as easy as it looks and you need a lot more than you actually think you do. Watch some video's of applications and the pro's use a sheet about 2~3 times bigger than the article to be covered. But take your time and it is doable. If you do cock it up, heat back up and try again, unless you put a big crease in it, which is possible. Found using the wife's hairdryer on a medium setting and slow speed worked fine. And degrease panel thoroughly before you start.

    IIRC - Sure you can buy pre-cut clear plastic panels to stick on ????
     
  3. Col_C

    Col_C I can't re...Member

    Aug 5, 2015
    1,431
    800
    Cornwall
    I've used the Triumph paint protection kit (Ventureshield) on SWMBO's Street Triple, just on the tanks sides where her knees rub. Obviously quite a bit thicker than what you would use for an all-over wrap, if you look really hard you can see the edges but invisible otherwise, would recommend.
     
  4. Moe

    Moe Senior Member

    Jun 10, 2015
    290
    113
    Colchester
    I've use this on tank sides on my gsxr, extreamly hard to fold round more curved panels.

    Mr Orange, wanted to do it all over so it's always protected.

    Think I'd do a proper detail first minus the wax obviously.
     
  5. Moe

    Moe Senior Member

    Jun 10, 2015
    290
    113
    Colchester
    I couldn't find one specific for the speed s yet
     
  6. Red Thunder

    Red Thunder Crème de la Crème

    Dec 2, 2014
    2,034
    1,000
    High Wycombe
    I just phoned my local Triumph dealer about this for my Speed Triple 2016 R and they also said it wasn't available, but suggested an Oxford product that comes as a clear sheet and you cut to size...said I would think about it.
     
  7. Moe

    Moe Senior Member

    Jun 10, 2015
    290
    113
    Colchester
    I've bought some from Amazon, used it before on gsxr and r1200, TIS only £7 for 1.5m x 30cm
     
  8. RoadSprocket

    RoadSprocket Active Member

    May 24, 2016
    39
    28
    United Kingdom
    I've wrapped my old KTM rear end and tank side panels before (not in clear vinyl), personally I think it would be challenging as your first try for the entire bike and you should expect it to take a day or two at least to get a quality finish. I've also got the mindset wrapping is a cheaper alternative to a decent respray, I don't see it as a paint-protection solution unless your using a professional grade product that supercar/hypercar owners throw a fair few thousand towards and then 100 labour hour charges on top.. compared to the £7 for a couple of meters on eBay. IMO there's better products for that above.
     
  9. GAJA

    GAJA Well-Known Member

    Sep 13, 2016
    48
    68
    London
    Have you considered stomp grips?
     
  10. Ali G

    Ali G Member

    Feb 6, 2017
    52
    18
    Kirkcaldy
    I had stomp grips fitted to gsxr750 and they scuffed the inside of my leathers. Wasn't that keen on them but they came with the bike. I think I'm gonna go with the ventureshield

    Ali
     
  11. Moe

    Moe Senior Member

    Jun 10, 2015
    290
    113
    Colchester
    I've had the same stuff on my gsxr that I've just bought again, very thick compared to coloured vinyl wrap.

    Watched the video, exactly how I've done it but I had to cut them using a shape Stanley knife.

    Hoping to get a full wrap on all the panels apart from the tank, will just do the sides.

    Got a good selection of carnubra wax and plastic finishers that I will use after.

    I'll post photos of before and after once I get round to it chaps.
     
  12. Moe

    Moe Senior Member

    Jun 10, 2015
    290
    113
    Colchester
    Before and after guys IMG_20170506_193728962.jpg IMG_20170506_193756685.jpg IMG_20170506_193748145.jpg IMG_20170506_193805568.jpg IMG_20170506_193805568.jpg IMG_20170506_193813080.jpg rather than wrapping the whole bike I polished out the swirl marks then wrapped the tank sides where most scratches occur.
    Then a coat of collinite wax, plastics done with trim restorer and matt metals with project 32 selent. Should only need top up wax every 6 months.
     
Loading...

Share This Page