Does This Dash-cam Exist?

This is the closest I've found.https://www.roadhawk.co.uk/roadhawk-ride-r-cycle-camera Both my self and the wife use one each on both the pushbike and M/C. I also have an extra, external battery which give the camera up to 4 hours power, They used to supply a wiring kit for the motorcycle too. Picture quality is good. I tend to run it at 720p and 50 frames per second

 

Not me Ade, although we had a chat about your Roadhawk on the GMU 2017 Sunday rideout.
It looked very neat indeed

 

That looks horny Ade, shame it costs over £15,000.

 

I have the roadhawk bullet myself tidy little cam helmet mounted Sena also do one called the Prism tube my Cousin Andy-K2 on this forum runs that type theyre both good cams for the cash.

 

I have the Roadhawk Bullet R Moto whatsit - like littleade.
No complaints so far.

 

I'm interested in this thread too as I'm looking for a cam for the same reasons as Greg / OP

 

There are a number of mounts supplied with the kit, including a curved tray for the side of your helmet. I use a sticky backed tray with the adjustable ball mount on the plastic cover of my radiator. I've also used the bar clamp mount to mount to the pillion peg bracket so I could have the camera facing backwards. Here's some footage I shot while on holiday in France a few years ago
T

 

I have just fitted a NextBase RIDE to my 1200 Explorer. I wired it directly to the battery as I didn't want to faff around connecting it up to the ignition. When connected to the ignition it turns on when the ignition is on. I have to remember to turn it on/off manually. You can download the manual from https://www.nextbase.co.uk/wp-content/uploads/2016/04/NBDVR-RIDE-Instruction-Manual-English-R01.pdf

 

£115 on EBay https://www.ebay.co.uk/itm/Nextbase...5464322?_trksid=p2349526.m4383.l4275.c10#rwid

 

Another vote for the Nextbase kit.

I have one in the car and it's definitely wire it in and forget about it.

I'm not sure about the bike camera but the car version comes with a cigarette lighter power lead. If you want to hard wire it they are more than happy to sell you a kit costing about £15.

This isn't necessary if you don't mind a bit of soldering. All you get in the kit is a fuse piggyback connector, a couple of quid off fleabay, and wire with a USB plug for the camera on one end and a black plastic box on the other.

The black plastic box contains the circuit to reduce the 12v coming from the battery to 5v for the USB camera.

You already have this circuit, it's in the cigarette socket connector. All you have to do is cut the plug off open it up and remover the circuit board. Connect the 12v side of the circuit board to the battery using the above mentioned fuse piggyback and then solder the lead on to the 5v side.

Cover the lot in heat shrink and you're done.

You don't even need the fuse piggyback connector if you're happy to wire it directly to a suitable feed in the fuse box or join it to a suitable 12v wire that comes on with the ignition.

 

Hi Greg
The kit on EBay claims [twice] to come with a hard-wiring option, so you should be good to go [and forget it], as long as you wire it via the ignition switch. However, it might be worth you going onto the Nextbase site and looking through FAQ's or "Contact".

Cheers, Steve

 

So it does, well spotted.

 

There's a lad I've been out with uses this system (Vsys x2) which has excellent quality and recommended.

http://www.szv-sys.com/m/productshow.asp?showidd=22&sID=001005

There's also these although can't say what there like.

https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.co.uk/ulk/itm/162678900722

https://www.amazon.com/VSYSTO-Motorcycle-Separated-Waterproof-Support/dp/B07C971CLY

 

And how much was the bike or did they throw it in to sweeten the deal on the camera!!! LOL.