Problems After Loading Tuneecu Map

Hi guys
I have a bit of a problem which I’m hoping someone more knowledgeable than me can help
I have 2 triumphs
A 2005 rocket standard and a 2004 tiger955i
Having successfully loaded a tuneecu map into my rocket (and boy did it make the bike sooo much better!!!) I decided to have a go at loading a map into my tiger since I had an aftermarket can for a few years and never got round to re-tuning it
I’ve loaded the 10173 map reprogramming went fine when I fired it up the idle was sitting at 2.5k rpm causing the manifold to overheat badly
I’ve tried to reprogram again but it has made no difference
Anyone has ever had this problem or have any idea what might be wrong?

 

Thanks for the reply
Yes I have thought of that but out of utter stupidity I can’t find it now so either I didn’t manage to save it or something happened to the folder!
Any ideas?

 

I did what the instructions say and reset the tps that’s all
It’s quite scary because the headers actually get red hot and the fan triggered within just a few minutes so I’ve turned the bike off and repeated the process again
I’ll give it another go tomorrow and see where I get to
Worst case I’ll have to get a stock map from someone and put it in I guess since I stupidly lost it
Thanks for the input

 

Thanks for the reply
Yes I have thought of that but out of utter stupidity I can’t find it now so either I didn’t manage to save it or something happened to the folder!
Any ideas?

 

I did what the instructions say and reset the tps that’s all
It’s quite scary because the headers actually get red hot and the fan triggered within just a few minutes so I’ve turned the bike off and repeated the process again
I’ll give it another go tomorrow and see where I get to
Worst case I’ll have to get a stock map from someone and put it in I guess since I stupidly lost it
Thanks for the input

 

thanks for the input
I have studied the process quite well before I did anything and as I said I have already downloaded a couple of maps to my rocket successfully
I did download the original map but I must have done something wrong when saving it and it got lost
When downloading the map I did everything as per instructions and reset tps..
I didn’t let it run the whole 12min tune as the headers were getting red hot (and I mean actually incandescent red!) and I just stopped the bike and repeated the remapping process thinking I might have done something wrong but was the exact same output..
should I let it run the whole 12min tune like this?

 

no worries man
Sometimes it’s the obvious I know!!

I’ve performed this 12 min tune in both my bikes a few times
My worry here is the heat
The bike was cold and since I’ve started it it took a few minutes for the fan to come on for the first time at which point I thought it was way too quick and that’s when I realised how much heat the fan was actually spreading out to me so then I looked at the headers and ye they were glowing

I’ve stopped it there and thinking I did something wrong I repeated the whole process but exact same thing happened ..
My cooling system is working fine
I’m not so worried about the bike overheating I’ll be watching it closely but more concerned about the heat generated around the headers and all the fixings where the fan is which is closely in front of it
I’ll give it another try
Thanks mate

 

i have a few actually I’m a gardener
How did I not think of that?
My neighbours are gonna love me today
Thanks pal

 

Ok
I’ve repeated download process just in case allowed time reset tps allowed time
Performed 12min tune with the help of the blower
Didn’t work

I’m gonna type some values to see if anyone can spot anything
With bike stopped :
Throttle pos 0.0%
Idle fuel adjustment 0.00%
Long term fuel trim 3.84%
Short term fuel trim 0.00%
Idle air control valve stepper position 180
Adaptive stepper position 227
Closed throttle position 2.4%

 

yes please mate
My email is jgonzalof100@yahoo.co.uk

thanks

 

I have a feeling that it’s actually nothing to do with the map and the tps might not have liked to have been reset or some other sensor
I’ll give it a go to put the stock map back in but the way it is behaving leads me to suspect it’ll be the same thing
Thanks guys for the advice