Scrambler Thoughts Regarding Fuel And Air Mixture...

Can a 2017 (Fuel injected) California bike switch from stock exhaust to aftermarket and plug the sensor holes on the exhaust? It does not throw any codes on the speedo. It does pop occasionally due to the "Off" mixture I am assuming but couldn't I get the bike remapped to make it run better like a 49th state bike?

The California bikes are mapped to "suck". While plugging those holes and just remapping it correctly, couldn't that increase some small horsepower gains for me?

Having issues finding anyone with a current EFI map for this full system exhaust I put on and the sensors wire are hanging in my way. Wondering if I could just eliminate them and gain horsepower at the same time?

I welcome questions and opinions.

Thank you.

 

Thank you. Checked out that site previously and feel that it has not been updated in quite some time. I am not feeling comfortable putting my motors trust in it. The quality cables are for sale on Amazon for less than $30 when I checked in case you need one.

 

I'm not seeing my bike on the list.

I just went out and took out the new full exhaust 2 block off plugs out of the exhaust. I then unplugged the 2 EFI sensors from the other end, twisted them in and then re-ran through, clipped them down, and plugged them back in to the electrical ends.

Almost midnight here so I cannot start it up without pissing off my neighbors. Gonna wait to morning to see if it runs without the popping.
(I previously ran it in the driveway with the sensor holes plugged with bolts and EFI sensors not plugged in) There were no "Check engine" lights or anything, just lots of popping. A Mechanic friend said if I rode it, it would have popped on a light though.

Allegedly the newer EFI bikes "ADJUST" by themselves to the aftermarket exhausts according to a few sources. (This is crazy to me because I come from other bikes in which I always had to remap and use power commanders.

We will see in the morning!!!

 

Started her up and took her to church this morning. Sounds fine but there is still popping on downshift and when I match revs on downshifts. I like the sound without the baffle so i will have to figure out next whether I need to Flash this ECU or will need a Powercommander.
Opinions are always welcome.

 

I have a 2017 Triumph Scrambler 900. It has two screw in sensors that go into the exhaust. (New and Old exhausts do). I have never had a Bonny before and this is my first Triumph so I am a little lost as to where the Bonny reference came from.

I switched out my stock exhaust to a High Desert TEC full exhaust. Was just trying to figure out the Air/Fuel mixture so it would not throw lights, pop, backfire, or blow up my motor.

I installed the sensors into the new exhaust. Still pops. Trying to sort it all out so I can remove the baffle for a better sound.

My conclusion is I will need to get a power commander or flash the ECU for an Arrow full exhaust map. (Closest exhaust map for their TEC exhaust from what I hear)
I am just trying to find that map right now for a nice deep, not popping exhaust on the bike.

Thank you for the link...Gonna check it out!

 

I have not changed any air mixture by touching anything regarding the air flow. Stock motor.

I have looked into TuneECU but all the maps seemed to be pre-historic and the site not updated. Not sure I trust it with my new bike. Looking for someone who currently has a map and will let me download it from them instead.

It's interesting how so many opinions are all over the place with this 2017 Triumph Scrambler. A triumph mechanic told me that the 2017 corrects itself so if I plug in the sensors to the new full exhaust, it will correct itself.
I can't say I believe him due to the fact that it sounds the exact same whether the sensors are plugged into the exhaust or not. Lots of popping on downshifts.

End result......I will somehow find someone with a 2017 that has an Arrow exhaust or TEC and willing to share the map with me. I will buy a PC cable and download it from someone's PC and remove the baffle from the exhaust. I will warm it up, carve a canyon, and downshift through all the corners listening for extreme popping!!

 

Thanks for posting the video. That guy is pretty awesome. Good videos. Lots of good info in them. I think I will try a re-map first and if still popping all the time, start yanking out pieces!!!

 

I have decided on this weekend's activities.....

Report back on the popping after I perform surgery on my bike and remove some excess fat.

 

Procedure done. Remapped, Bike is amazing now. Peppier, and no popping even on the downshifts.

 

I have the Arrow Full 2 in 1 map.
No engine mods except for removing the crappy CA emissions bundle like the video above that shows Delboy doing it all. Only have 1500 miles so most mods have been aesthetic to this point and I don't want this bike as my fast bike. This is my "Posing" bike to not even lie. I bought it to have a good looking bike unlike my other track bikes that were always being thrown around at high speeds. Lol