Rear Footpeg Removal

Here's what I did - not overly elegant, but sort of blends in...

The original bolts won't seat, because the holes are not deep enough (when the pegs are removed) to accommodate their length.

For the offside, I stuck on PVC tape patches, just to keep the moisture out as a temporary measure...but they've been there for 5 months and you honestly can't see them.

The nearside shares one of the bolts for the exhaust hanger - and remember without the peg, you can't re-tighten the bolt. I used a couple of bushes and rubbers that were saved when removing a standard Daytona exhaust...and job done.

 

Definitely cover them. Blank off plugs on mine.

 

http://www.ebay.co.uk/itm/Round-Pla...hash=item1c75270417:m:mVeMiDS3Fhr6dGq8HSLDjgQ

 

I mistyped 'Blank Plugs' and got this instead - http://www.ebay.co.uk/itm/Pug-A6-Bl...hash=item41559aa617:m:mfW2gpfJb_U-8vr_GeVvG7w

Update: I've ordered the pugs and will cut out their faces and stick them over the holes. Perfect.

 

I think all of those look too big Danny - it's an 8mm bolt and the smallest plug from that seller is a 10mm.

 

These might fit

http://www.halfords.com/workshop-to...kk9JH6BHZPkJFgAdUPJfnWA5rwhfCd8cHEaAn3A8P8HAQ

 

You'll need a shorter bolt for the exhaust bracket anyway, so why not just get four of them?

 

Will these OEM plates fit?

http://triumphinstructions.com/ProdDocs/A9708094-EN.pdf

 

I'm guessing they apply to a much earlier model (or it's a mistake).

The bolts removed with the pillion pegs are threaded directly into the sub-frame - the holes are not drilled through and a nut isn't needed. You can't pass a bolt through the hole and fit a nut to the other end.

You really only need a shorter bolt or a blanking plug.

 

Can't you just fit a shorter length bolt of the same thread? I would dig some out of me bolt boxes.

 

Just removed my rear pegs (as i have removed the underseat exhausts and put on a single side SC project unit) and dont have a rear seat cover however, I would expect that having the tail pack on the rear seat would make it obvious enough that I am not carrying passengers...
Plus I have used one of the holes to secure the compressor for a 'Denali Split Soundbomb' horn
I would need to put somehting in the top of the hole to stop water pooling above the bolt though as the hole goes straight through on the rear bolt for the pegs.
On the other side I will be installing my Scottoiler resevouir

 

I just removed the pillion peg on mine and fitted a seat cowl. I just got 4 M8 12mm long stainless bolts. on the seat cowl shame the colour doesn't match the rest of the bike ............................ genuine Triumph I read some where else this is the norm?

 

Fitting shorter bolts has to be the ideal solution - I'm taking your lead and will order some too.

My seat cowl doesn't match either - and it seems that others are reporting the same thing. Sadly, it's the norm.

 

You have a supplier called demon tweaks (based in Wrexham I believe and I miss them dearly!) they can probably supply 8mm standard pitch, alloy, stainless or anodized bolts in pretty much any length or colour that floats your boat, make sure when you order that bolts have no shoulder (thread goes all the way to the head) Alloy are prob better as the sub frame is alloy as well and wont create oxidization. Prob also put a washer in Original bolts were for tensile strength as needed to safely carry weight of pillion hence they are stainless from the factory.